Cleveland MKDT-12-T Betriebsanleitung

SE95010 Rev. 9Operators ManualInstallation, Operation & ServiceGas Table Top KettlesMODELS:KGT-6-TKGT-12-T1333 East 179th St., Cleveland, Ohio, U.

CONSOLE COMPONENTS(used after June 2005)ITEM # PART # DESCRIPTION QTY.1. KE600545 COMPONENT MOUNTING BRACKET . . . . . . . . . . . . . . . . . . . .

CONSOLE COMPONENTS(used prior to June 2005)ITEM # PART # DESCRIPTION QTY.1-8 KE01928-3 COMPONENT PLATE ASSEMBLY . . . . . . . . . . . . . . . . . . .

OVERHEADVIEW321ITEM # PART # DESCRIPTION QTY.1. FA21024 HEX NUT, SS, 5/16-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SWITCHES & INDICATORS(used after June 2005)KE600560-B23567891410OFF412563ITEM # PART # DESCRIPTION QTY.1. KE55486-3 INDICATOR LIGHT, GREEN . . .

SWITCHES & INDICATORS(used prior to June 2005)565423185 7ITEM # PART # DESCRIPTION QTY.1. SE00114 POTENTIOMETER WITH ON/OFF SWITCH, C/W ITEM #2 .

12356171819SEEFAUCETDRAWING20 212825262728422232478ITEM # PART # DESCRIPTION QTY.1. SK50403 BRONZE BEARING . . . . . . . . . . . . . . . . . . . . .

PIPING ASSEMBLYTO MAIN GASSUPPLY14562143111081316177915

ITEM # PART # DESCRIPTION QTY.1. KE01929-1 FEED PIPE ASS'Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleveland Range equipment requires little preventative maintenance. We do however provide the followingchart as a guideline for inspection and mainte

CALIBRATING PROCEDURE1. Insure the unit has a vacuum before you begincalibrating procedures. If unit requires venting referto Kettle Venting Instructi

FOR THE USERIMPORTANTPOST IN A PROMINENT LOCATION, INSTRUCTIONS TO BE FOLLOWED IN THE EVENTTHE USER SMELLS GAS. THIS INFORMATION SHALL BE OBTAINED BY

RESERVOIR FILLPROCEDURESThe kettle's water level must be maintained at theproper level. Under normal operating conditions, thesealed water reserv

KETTLE JACKET CLEANOUT AND PASSIVATION PROCEDURESThe following procedure should be preformed at least once every three years to prevent possible corro

KETTLE VENTINGINSTRUCTIONS1. Turn kettle ON and setTemperature Control to 10(Max.), heat the empty kettleuntil unit cycles off.2. Vent kettle by pulli

WIRINGDIAGRAM44101311153141251 288967ITEM # PART # DESCRIPTION1. KE55486-2 L.E.D., RED (USED AFTER JUNE 2005)KE50567-1 L.E.D., RED (USED PRIOR TO JUNE

OPERATING SEQUENCES1. Turn On-Off Switch/ * 14 volt transformer is energized and powers solid state control system. Temperature Control Knob "ON&

MARINE LOCKTESTING PROCEDURE1. Check that lock clears stop pin on side box withoutrubbing when kettle is tilted (Figure A).2. Check side to side play.

INSPECTIONBefore unpacking visually inspect the unit for evidenceof damage during shipping.If damage is noticed, do not unpack the unit, followshippin

Installation must be in accordance with local codes and/orthe National Fuel Gas Code ANSI Z223.1 Latest Edition(USA) or the latest Installation Codes

678543219OPERATING INSTRUCTIONSITEM # DESCRIPTION FUNCTION1. Tilting Handle Used for tilting the kettle.2. Vacuum/Pressure Gauge Indicate steam pressu

OPERATING THE KETTLEDO NOT ATTEMPT TO OPERATE THIS APPLIANCEDURING A POWER FAILURE.KEEP APPLIANCE AND AREA FREE AND CLEAR OFCOMBUSTIBLES.DO NOT LEAN O

MARINE LOCK Your unit is equipped with a marinelock to prevent accidental tilting.The following procedure should beused to tilt the kettle. 1. Grasp

STAINLESS STEEL EQUIPMENT CARE AND CLEANING(Suppied courtesy of Nafem. For more information visit their web site at www.nafem.org)Contrary to popular

SERVICE PARTSWARRANTYOur Company supports a worldwide network of Maintenance and Repair Centers. Contact your nearest Maintenance andRepair Centre for